Product Questions and Answers
Do you have a question about this product? Then we would like to ask you to first look through the existing questions and answers, most likely your question has already been answered and you will get the desired information much faster this way. Your question is not listed? Then please click on the button "Ask a question".
If you have not found a suitable answer, you can ask your question here.
The programme "ComPortMan" by Uwe Sieber should make it possible to set the COM-port numbers permanently. You may want to try it out: www.uwe-sieber.de/ComPortMan.html Please note that this software does not originate from us and we therefore cannot assume any guarantee for it.
Baader Steeldrive II motor focuser for Diamond Steeltrack® Focusers and other Focusers
The SD II motor unit is designed to be operated with the SD II control unit. If you want to use the motor without the Stedldrive II Control unit, you can find a diagram with the pin configuration for a self-made control in our manual (pdf). A control unit can control one motor unit at a time, but you can use a computer to control several controllers parallel.
The motor is designed to move to a saved position with highest precision if it is used together with the homing sensor – even if it has to move several kilograms over the complete travel of the focuser! The Steeldrive II Motor Focuser includesone motor unit with belt drive and a 3m long connection cable. It can be connected to all Baader Steeltrack® and Diamond Steeltrack® focusers. A 3D-printed magent holder for homing sensor, which can be attached to the focuser. For Baader Diamond Steeltrack® focusers, a Metal Magnet Ring for Homing Sensor (Steeldrive II) (#2957264 , € 73) is available separatley.
The motor unit of the Baader Steeldrive II can easily be attached to focusers with a dovetail clamp. A Baader Diamond Steeltrack® focuser ialready provides a matching 25mm dovetail, as well as the previous Classic 2" or 3" Steeltrack® modells (25 mm or 27 mm dovetail). Other focusers can also be used, but they may need other adapters, which will either be offered by us in the future or must be custom-made by you.
SD II Motor Unit
SteelGo II Software
SD II Controller
Video: Steeldrive II – Installation of
Motor Unit and Magnet Holder
Video: SteelGo II – Working with the Software
Video: Steeldrive II – Controller
Installation and Functions
Scope of Delivery of the Motor Unit for Steeltrack® Focusers
- Steeldrive II (SD II) motor unit for Steeltrack ® focusers
- CAT 7 cable (3 m) to connect the control unit
- SD II toothed belt for Steeltrack® focuser
- Temperature sensor with phone connector. Can be used with SD II motor units or SD II control units
- Magnet holder for homing-sensor – can be used with Diamond Steeltrack® and similar focusers, includes mounting screw
- Allen key (2 mm)
- Velcro tapes (cable ties) for strain-relieving cable management
- Additional Temperature sensor for Steeldrive II, cable included (#2957263 , € 21)
- Metal Magnet Ring for Homing Sensor (Steeldrive II) (#2957264 , € 73) – fitting for Baader Diamond Steeltrack® focusers
- Mini DIN / Cinch adapter cable to connect heat pads (Steeldrive II) (#2957262 , € 29)
For further accessories like adapters to use the SD-II motor unit with other focusers, please visit www.baader-planetarium.com/bds
- High precision focusing of heavy loads
The high-torque stepper motor is directly engaged with the focuser via a timing belt. This eliminates the backlash (and potential cause of defects) induced by gearboxes which would have to be used with lower power motors. The Steeldrive II can quickly move loads up to 8 kg with high precision. The focusing resolution is 2.5μm.
- Intuitive Operation. The motor unit requires the
Steeldrive II Controller
(#2957260 , € 445)
The intuitive hand control makes it possible to find and save the focus point very fast. Several modes are available to move the focuser:
Normal mode: The focuser moves as long as a key is pressed.
Jogging mode: Each keystroke moves the focuser for a distance which is configurable in the SteelGo-software (e.g. 0.1 mm).
Single step mod: Each keystroke moves the focuser for the smallest possible way (ca. 2.5 micrometer).
The configuration of limits, saving and resetting of positions and (de)activating of the temperature control can also be done with the hand control. Brightness of backlight illumination and status LEDs are also configurable.
- Contactless Homing Sensor
The Steeldrive II motor unit features a contactless (wearfree) homing sensor (hall-effect sensor). It is activated by a magnet attached to the moving part of the focuser. It enables precise homing and repeatable approach of saved absolute positions as well as reference of the mechanical endstop. A simple mount for this magnet to be attached to the focuser is included in the scope of delivery. For Baader Diamond Steeltrack® focusers, an adapterring made of metal is available separately.
However the Steeldrive II can also be used without the homing sensor as the absolute position is kept in a persistant circular eeprom buffer. Even if a power failure occures, the absolute position is loaded upon restart of the Steeldrive II, as long as the focuser wasn't moved by hand.
- Temperature Compensation
Two digital temperature sensors may be used simultaneously. One of each may be connected to the motor- and the controller unit. For the automatic temperature compensation, the specific sensor to be used can be selected, or the average temperature of both sensors may be used (eg. measuring the temperature above and below the telescope tube, or inside and outside), depending on your needs. The temperature compensation factor is for example calculated with the SteelGO software and can then be saved locally on the Steeldrive II controller unit. The compensation period and ∆T threshold can also be adjusted. The temperature compensation may then also be used in standalone mode of operation (without a connected computer).
- 12V/1A PWM power output (PID-controllable)
The Steeldrive II features a 12V/1A power output. It can be used with an optionally available adapter cable from Steeldrive II Controller AUX Port to Cinch with common dew-cap heaters #2957262 with up to 10W. The power can either be set in the SteelGo software, or you set a desired temperature for one of the temperature sensors. This prevents undesired heating of the telescope, because you keep the dew cap just above the dew point. It can also be used to control the exact temperature (+/-0.1 °C) of e.g. optical filters.
- Made in Germany
All mechanical parts are CNC-milled from Aluminium in our workshop. The electronical boards are also designed and made in Germany. We only use high-end electronical components. The electronic circuit boards are additionally protective coated.
- Low Power Consumption
The motor current is automatically reduced while in holding state. The Steeldrive II then consumes approximately 0.7 W.
|Net weight (kg)||0.35|
|Payload Capacity (kg)||up to 8 kg|
|Resolution||appr. 2,7 micrometer per step|
|Power Output||12V/1A PWM|
|Power consumption||ca. 0,7 Watt|
|Software||SteelGo Software (Download)|
> 500 Downloads
SteelGo II Installer for Windows 10 in 32- and 64-bit version.
SteelGo II Software Version 1.11
SteelGo II Firmware Version 1.130
> 100 Downloads